ViiK Parking Occupancy system
Available in Japanese market only
| Products Name |
|---|
| OPS-01SS [Wireless vehicle sensor] |
| OPS-01GW [Gateway] |
| OPS-01MF [Repeater] |
Features
Sensor detects vehicle and send the status wirelessly.
Possible to install easily for existing parking or temporary one.
The sensor is battery operated, so no hardwire required.
Since the battery lasts approximately 5 years, it doesn’t require any maintenance. Also the battery is replaceable and it will help to save the equipment replacement cost.
This sensor could be installed to concrete, asphalt or gravel surface by changing bolts or anchor pins.
Use a repeater for installation on a large site.
If the radio signal from the sensor doesn’t reach to the gateway because of long range or some building which blocks the signal, our multi-function unit will help to be a repeater.The unit can be a transmitter and a receiver as well.
Examples of installation facility
Wireless spec
Specifications
(Wireless vehicle sensor)Specifications
(Gateway)Specifications
(Repeater)
|
Wireless frequency |
920MHz |
|---|---|
|
Wireless range |
100m(open range) |
|
Wireless standard |
Telec (Japan) |
|
Model |
OPS-01SS |
|---|---|
|
Detection method |
Wireless Magnetometer |
|
Response time |
Entering : 4sec |
|
Maximum car floor height |
400mm |
|
Power supply |
Dedicated Lithium battery |
|
Battery life |
Approximately 5 years |
|
Detection target |
Passenger car |
|
Max. load |
4t max. |
|
Surface condition |
Concrete / Asphalt / Gravel |
|
Unusable condition |
Metal object is placed close to the sensor |
|
Dimension |
W243 x H157 x D39 (mm) |
|
Weight |
1000g (incl battery) |
|
Operation temperature |
－20 to 60 [℃] |
|
Operation humidity |
93% max. |
|
Degree of protection |
IP67 |
|
Accessories |
Screw cap 4pcs |
| Model | OPS-01GW | |
|---|---|---|
| Power supply | AC/DC12 - 24V | |
| Power consumption | Max. 3W | |
| Input | Power | AC/DC12 - 24V |
| Output | Trouble | Dry contact (DC30V / 0.3A) |
| Relay1 | Dry contact (DC30V / 0.3A)) | |
| Relay2 | Dry contact (DC30V / 0.3A)) | |
| Additional Interface | RS485 hald duplex | Half duplex 115200bps Max.32node |
| RS485 EOL selectable | 2P switch : 120 ohm /NC | |
| Micro USB | Micro USB 2.0 | |
| Operation temperature | －10 ~ 60 [℃] | |
| Operation humidity | 85% max. (non-condensing) | |
| Degree of protection | N/A | |
| Install location | Waterproof electrical box | |
| Installation height | <1.5m (from ground to bottom of this device) | |
| Dimension | W175 x H175 x D75 (mm) | |
| Weight | 750g | |
| Accessories | Antenna, tool for Antenna installation | |
| Model | OPS-01MF | |
|---|---|---|
| Power supply | DC12 - 24V | |
| Power consumption | 0.5W | |
| Mode | Repeater : Repeat wireless signal from sensor to gateway Output : Possible to control external device by using relay output Input : Possible to send input signal to gateway |
|
| Input | Power supply | DC12 - 24V (usable cable AWG23 to 25) |
| Signal input | NO input contact | |
| Output | Relay1 | Dry contact (DC30V / 0.3A) |
| Relay2 | Dry contact (DC30V / 0.3A) | |
| Operation temperature | －20 ~ 60 [℃] | |
| Operation humidity | 85% max. (non-condensing) | |
| Degree of protection | IPx5 | |
| Install location | Indoor/outdoor Wall mount/ Pole mount (option necessary OWU-PA1) | |
| Installation height | <1.5m (from ground to bottom of this device) | |
| Dimension | W70 x H134 x D33 (mm) | |
| Weight | 170g | |
| Accessories | 1pcs:Antenna, 1pcs:tool for Antenna installation 2pcs:mounting screws for wall mount |
|